Admin : a renommé Cisco ISDN en Cisco RNIS debug

2009-03-03T15:53:41Z

a renommé Cisco ISDN en Cisco RNIS debug

← Version précédente	Version du 3 mars 2009 à 15:53
(Aucune différence)

Admin le 3 mars 2009 à 15:45

2009-03-03T15:45:33Z

← Version précédente		Version du 3 mars 2009 à 15:45
Ligne 104 :		Ligne 104 :
	If the router is not attempting to dial then there is a problem with the config.		If the router is not attempting to dial then there is a problem with the config.

	[[Catégorie:~~Network-Clara~~]]		[[Catégorie:Cisco]]

212.43.232.68 : Page créée avec « First find the config on churchill. Then telnet to the router's ethernet interface IP address or framed ip address or the the static nat mapping on port 23. eg: ip nat insid... »

2009-03-03T14:25:59Z

Page créée avec « First find the config on churchill. Then telnet to the router's ethernet interface IP address or framed ip address or the the static nat mapping on port 23. eg: ip nat insid... »

Nouvelle page

First find the config on churchill.
Then telnet to the router's ethernet interface IP address or framed ip address or the the static nat mapping on port 23. eg:

ip nat inside source static tcp 192.168.162.254 23 80.168.107.232 23 extendable

At the prompt:

router#

type show isdn status

If all is well the output should look like this:

LongboreLtd#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
CCB:callid=946A, sapi=0, ces=1, B-chan=1, calltype=DATA, hdlctype=HDLC-T RUNK
Active dsl 0 CCBs = 1
The Free Channel Mask: 0x80000002
Total Allocated ISDN CCBs = 1

If the output looks like this:

Router#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0

Notice that the layer 1 status is DEACTIVATED
and that layer 2 is NOT Activated. This means that there is no physical layer or datalink layer signals being picked up by the cisco. This could be that the isdn cable is broken or
not plugged in properly or that there is a problem with the ISDN line itself.

Next debug the dialling events:

Router#debug dialer events
Dial on demand events debugging is on

Make sure the debugging is outputting to the console

Router#terminal monitor
% Console already monitors

Then attempt to ping something

Router#ping
Protocol [ip]:
Target IP address: 195.8.69.7
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 195.8.69.7, timeout is 2 seconds:

*Mar 1 00:25:14.535: BR0 DDR: rotor dialout [best] least recent failure is also most recent failure
*Mar 1 00:25:14.535: BR0 DDR: rotor dialout [best] also has most recent failure

*Mar 1 00:25:14.539: BR0 DDR: rotor dialout [best]
*Mar 1 00:25:14.539: BR0 DDR: place call
*Mar 1 00:25:14.539: BR0 DDR: Dialing cause ip (s=212.188.147.193, d=195.8.69.7)
*Mar 1 00:25:14.543: BR0 DDR: Attempting to dial 08451264000.
Success rate is 0 percent (0/1)

*Mar 1 00:25:16.579: BRI0: wait for isdn carrier timeout, call id=0x8009

*Mar 1 00:20:15.691: BR0 DDR: rotor dialout [best] also has most recent failure

*Mar 1 00:20:15.695: BR0 DDR: rotor dialout [best]
*Mar 1 00:20:15.695: BR0 DDR: place call
*Mar 1 00:20:15.695: BR0 DDR: Dialing cause ip (s=212.188.147.193, d=195.8.69.7)
*Mar 1 00:20:15.699: BR0 DDR: Attempting to dial 08451264000
*Mar 1 00:20:15.699: BRI0: wait for isdn carrier timeout, call id=0x8006
*Mar 1 00:20:15.703: DDR: Dialing failed, 1 packets unqueued and discarded.
*Mar 1 00:20:17.691: BR0 DDR: rotor dialout [best] least recent failure is also most recent failure
*Mar 1 00:25:16.583: DDR: Dialing failed, 5 packets unqueued and discarded

Questions to ask:

1> Is the router attempting to dial out.

2> If the router is attempting to dial then you is there a carrier timout. This will usually mean that there is a problem with the isdn line, the two major possibilities being a faulty line or they need a 9 for an outside line.

If the router is not attempting to dial then there is a problem with the config.

[[Catégorie:Network-Clara]]

Cisco RNIS debug - Historique des versions

Admin : a renommé Cisco ISDN en Cisco RNIS debug

Admin le 3 mars 2009 à 15:45

212.43.232.68 : Page créée avec « First find the config on churchill. Then telnet to the router's ethernet interface IP address or framed ip address or the the static nat mapping on port 23. eg: ip nat insid... »